By “TrapRJohn” Enos, trapper, hunter, mountain man and atlatlist, about a 2003 trip with Bob. Shared with his permission. Check state laws before you fish with an atlatl.
In mid-February this year, I (from the woods of New Hampshire) and a good friend, Bob Berg (from the Finger Lakes area of New York), decided we’d had enough of the deep-freeze winter we were trapped in. The answer was a trip to Florida, Georgia and Alabama! The trip had two purposes: atlatl fishing and atlatl hunting for wild boar (another story for another time), and attending the Paynes Prairie Knap-In near Micanopy, Florida, and the Knap-In at Moundville, Alabama, the next weekend.
The problem: how to make a stable, inexpensive platform on the water for throwing darts with the atlatl.
What you need
- Two canoes, 15 feet or longer, owned or rented
- Two lengths of schedule 40 PVC pipe (it comes in 10-foot lengths; cut 18 inches off each). Two 2×4s or two stout branches would probably work too.
- A roll of duct tape (or four long lengths of heavy twine or light rope)
- For night fishing: lantern holders made from two lengths of ½-inch galvanized pipe, bent so one end hooks under the canoe seat and the middle has a 180-degree bend that hangs out over the water. Saplings or bamboo would work too.
How we built it
There were four of us: me, Bob Berg, “Leggs” (a friend from Kentucky), and Paul Weigel, a 16-year-old German exchange student and world champion atlatlist who was staying with Bob and his family. We set the two canoes side by side at the water, turned so the stern became the bow. Then we tightly taped the PVC pipes onto the canoe braces, making sure the pipes lay along the full length of each brace and against the outside gunwale of first one canoe, then the other.
If your canoe braces are different lengths and the canoes don’t end up exactly parallel, cut one of the pipes a different length so they track straight through the water.
Next we taped the bent conduit to the front of each canoe, with one end under the seat and the bend hanging out over the water, taped a straight length of conduit to it, and hung a two-mantle propane lantern from the end. A heavy waxed line from the lantern’s tank to the conduit tipped the lantern a bit less than 45 degrees, shining into the water. A piece of flashing bolted to the back of the lantern top made an excellent shield to keep the light out of our eyes, and worked as a reflector onto the water.
Load your gear (life jackets, paddles, atlatls and darts), light the lanterns, and you’re ready for an adventure!
The test
About half a mile upriver we pulled into the first backwater. With Leggs paddling from the stern of the right canoe, Paul stood up in the bow of the left canoe, fitted a dart to his atlatl and started looking for fish. The canoes seemed stable! Bob stood up in the bow of the right canoe. Still stable! The first dart was thrown at a fish with minimal wobble. At one point four, and another time five, of us were standing, and the canoes stayed stable enough for safe and effective atlatl (and bow) shooting.
I have trouble with my balance, so the next time out we brought a cheap folding armchair and two small pieces of ½-inch plywood for its legs to sit on (to keep them from punching through the canoe bottom), and taped the chair to the rear brace. That made a stable seat from which I could still use the atlatl, though standing is better if you can.
The whole setup cost about $50, and could be done for less. Coupled with the inexpensive sport of atlatling, this kind of fishing trip is doable, fun and can result in some good eating!
How many fish did we get? That’s a whole other story, but I will say that Paul skunked the rest of us, darting five shad in two nights and hitting every one in the head. Cooked over our campfire, the shad were bony but very tasty!
